Tampa Office

Category: Commercial Doors

Model 3400: Miami-Dade County Certified Wind Load Rated Rolling Sheet Door

Model 3400: Miami-Dade County Certified Wind Load Rated Rolling Sheet Door

The Model 3400 series commercial roll up door has been specifically engineered for Miami-Dade County, Florida. With an ability to withstand high winds, the sheet metal door meets Miami-Dade County’s stringent building codes. The door is also easy to install and uses a 12” drum wheel. Other features and specific measurements of the door are as follows:

  • Maximum opening size of 12’ wide x 16’ high (192 sq.ft.)
  • Push-up, hand chain, and electric operations
  • PSF Ratings:
    • +43 PSF and -49 PSF
DOWNLOAD FLYER

Curtain

  • 24-gauge galvanized corrugated steel
  • Grade 80 galvanized steel
  • Available in white only
  • Super Durable polyester paint coatings, which are corrosion resistant
  • Wash coat over primer interior side
  • 40-year film integrity warranty – up to 30-year chalk and fade
  • Flexible nylon wear strips

Bottom Bar

  • 24-gauge acrylic-coated galvalumed roll formed steel
  • 2” x 1 ½” galvanized angle
  • Bulb astragal (Durometer 75)
  • Stainless steel nuts and bolts

Axle/Torque Tube

  • Oil tempered torsion springs conforming to ASTM A229
  • 16-gauge, 12” diameter galvanized drum
  • Low friction, grease-filled steel ball bearings staked in each drum
  • 26-gauge spiral torque tubing houses axle assembly

 

Guides

  • 12-gauge galvanized steel guide, with 11-gauge windlock bar spot welded guide
  • Bolt on head stop ¼” thick steel
  • 2 7/8” guide depth
  • Pre-punched for lock and attachment bolts
  • Vinyl guide wear strip

Hardware

  • Bottom bar mounted 10-gauge slide locks – 2 per door
  • Bottom bar mounted 16-gauge step plate – 2 per door
  • 12-gauge door mounting brackets
  • 1-5/16” tension holding device

Model 850: Miami-Dade Certified Wind Load Self Storage Door

Model 850: Miami-Dade Certified Wind Load Self Storage Door

The 24-gauge corrugated door curtain is manufactured from full hard galvanized grade 80 steel and coated with Super Durable polyester paint that is backed by a 40-year film integrity and a 25 year no-fade limited paint warranty. Independently tested, the Model 850 meets the requirements of the Miami-Dade County Product Control Division for the high velocity hurricane zone (HVHZ) of the Florida building Code. Design wind load is rated +46 PSF and -54 PSF. Available in opening sizes up to 8’8” x 10’0” and in white only.

DOWNLOAD FLYER

Door Springs

During production, each spring is coated with a generous amount of grease that penetrates the pores of the spring with additives, displacing moisture and preventing the formation of rust and corrosion. In addition, this process relieves the friction created between spring coils thereby providing smoother door operation. Finally, the spring and axle assembly is enclosed in a tube to protect them from the elements encountered throughout the life of the door.

Optional Package Protection and Shipping

Doors stacked on top of each other in transit are going to shift… unless they can be packaged in a way to minimize the sliding that occurs during that time. Janus has found the way. As an option, we can suspend each door individually in crates. Whether they travel down the block or across the country, compaction damages, door abrasion and chatter marks are virtually eliminated.

Ratchet Tensioning Device

The Janus ratchet tensioning device supplied as standard equipment on our door offers a simpler method of tensioning while more accurately fine tuning all the springs on the door at the same time. There is no extra hardware required. Eight different positions on the tension wheel allow one to perfectly balance the door every time. There are no pins required to hold the tension on the spring. You simply just click it.

Radial Ball Bearings

Janus supplies radial ball bearings at no additional cost. Our permanently lubricated bearings require no maintenance and are guaranteed to last the entire life span of the door.

Dead Axle and Torque Tube Assembly

This design, noted for its durability and smoother operation with commercial applications, has now been incorporated into the Janus self-storage door. The tube housing protects the springs and strengthens the axle. Eliminating axle push and shift that can occur with a live axle, the dead axle design allows for a straighter travel path of the door curtain in the guides. The biggest feature of this design is that it affords the fine tuning of any spring adjustment to equally affect all springs on the door at the same time.

Latching

Our patented mini latch features a cover plate made from a heavy gauge yellow zinc coated steel or optional stainless steel. In addition, the latch cover protects the slide from tampering by completely covering the slide, with the exception of a tab used to operate the latch. To further secure the door, the latch’s two-inch throw, with its magnetic properties, can be incorporated with the new guide-mounted security devices. This versatile design affords you the ability to utilize padlocks, cylinder locks or both.

Model 750: Certified Wind Load Self-Storage Roll Up Door

Model 750: Certified Wind Load Self-Storage Roll Up Door

Janus International has achieved wind load certification with the Series 750 Steel Roll Up Door. The Series 750 Certified Wind Load Self Storage Door was designed to meet stringent wind load requirements for mini storage applications while still providing the best door operation in the industry. The innovative door design has minimized the locking and reinforcement needed to strengthen the door to pass rigorous wind load testing.

Product Brochure

FEATURES

  • Minimizes the locking and reinforcement needed to strengthen the door to pass rigorous wind load testing.
  • Fewer friction points and less additional weight results in a door that operates better and still yields greater strength than any other available to the self-storage industry.
  • Meets the requirements of the SBC (Standard Building Code) and ASCE 7 (American Society of Engineers). The ASCE Standard is used in the Florida Building Code and the International Building Code.
  • Applicable opening sizes range from 3’ wide through 10’ wide, with the maximum height being 12’
  • Locking device may be located on the curtain or the bottom bar.
  • Doors may be installed on steel, concrete, or filled block jambs
  • All door sizes meet the wind load requirements of the interior and exterior zones for 100 mph SBC wind speed and 130 mph exposure B, ASCE 7 wind speed.
  • Higher wind load ratings are available for certain sizes and can be determined on an individual basis.

Model 650: Self Storage Roll-Up Doors

Model 650: Self Storage Roll-Up Doors

The Janus International Series 650 steel roll up door has been designed and manufactured to give self-storage facility owners a high amount of value, as the 650 mini storage roll up doors are extremely durable and require virtually no maintenance. Janus doors provide long term savings that it brings when installation, maintenance, and replacement costs. Each metal roll up door comes with a three year workmanship and material warranty. Additionally, a 40-year film integrity and a 30 year no-fade policy for the paint

Product Brochure

Door Springs

  • Coated with grease during production, which prevents rust and corrosion
  • Enclosed in a tube for lifetime protection
  • Provide for smooth door operation

Ratchet Tensioning Device

  • Allows for simplified spring tensioning
  • Tensions all springs at once
  • Requires no pins to hold the tension on the spring

Radial Ball Bearings

  • Provided at no additional cost
  • Permanently lubricated
  • Require virtually no maintenance

Dead Axle and Torque Tube Assembly

  • Tube housing protects springs and strengthens the axle
  • Eliminates axle push and shift that a live axle would create
  • Allows for springs to be turned all at the same time

Model 3100: Certified Wind Load Rated Metal Roll Up Doors

Model 3100: Certified Wind Load Rated Metal Roll Up Doors

The Janus International 3100 series is our certified wind load rated model that has been manufactured to withstand strong wind forces. Independent laboratory testing has verified that the Model 3100 steel roll up door meets stringent building codes, while the included one-year warranty ensures its quality

Product Brochure

Wind Load

  • Designed to meet stringent building codes in coastal regions
  • Utilizes 12” drum wheel
  • Maximum opening size of 20’ wide x 14’ high (280 sq. ft.)
  • Push-up, hand chain and electric operations
  • PSF Ratings:
    • +35 PSF and -41 PSF for opening widths through 12’
    • +35 PSF and -38 PSF for opening widths over 12’ through 16’

Curtain

  • 26’gauge galvanized corrugated steel
  • Grade 80 galvanized steel
  • 20 standard colors (special colors upon request for a nominal upcharge)
  • Super Durable polyester paint coatings, which are corrosion resistant
  • Wash coat over primer interior side
  • 40-year film integrity warranty – up to 30-year chalk and fade
  • Flexible nylon wear strips

Bottom Bar

  • 24-gauge acrylic-coated galvalumed roll formed steel
  • 2” x 1 1/2” galvanized angle
  • Bulb astragal (Durometer 75)

Guides

  • 12-gauge galvanized steel guide, with 11-gauge windlock bar spot welded guide
  • Bolt on head stop ¼” thick steel
  • 2-7/8” guide depth
  • Pre-punched for lock and attachment bolts
  • Vinyl guide wear strip
  • Universal jamb mount

Hardware

  • Bottom bar mounted 10-gauge slide locks – 2 per door
  • Bottom bar mounted 16-gauge step plate – 2 per door
  • 12-gauge door mounting brackets

Model 6500: Counter Shutter

Model 6500: Counter Shutter

The 6500 series roll-up doors offer the best in security, flexibility, and appeal. Reduced sized slats provide for smoother operation and a more aesthetically pleasing appearance. End users and specifiers recognize the 6500 Series as state-of0the-art in design, fit, and finish, yet appreciate the simplicity and practically that define the product.

SPECIFICATIONS AND OPTIONS

6522 6544 6566
CURTAIN
Flat slat S S S
Exterior Skin
22 gauge, Galvanized [G/W/P/U] S – –
16 gauge (.050”), Extruded aluminum [C/P] – S –
22 gauge, Stainless steel [#4] – – S
BOTTOM BAR
Extruded aluminum [C] S S –
11 gauge, Stainless steel – – S
Tubular stainless steel – – 0
LOCKS
Thumb turn lock and handle S1 S1 O2
Keyed lock and handle 0 0 02
Best cylinder 0 0 02
Stainless steel slide locks – – S
HOOD & HEADPLATE COVERS
24 gauge, Galvanized [G/W/T/U/P] S – –
20 gauge, Aluminum [C/P] – S –
24 gauge, Stainless steel [#4] – – S
GUIDES Fabricated from two pieces of extruded aluminum or formed stainless steel to create guide channel. Guide angles include curtain stops and flared guides.
Extruded aluminum [C] S S S
11 gauge, Stainless steel [#4] — — O
OPERATION
Manual Operation S3 S3 S3
Awning Crank O4 O4 O4
Tube Motor O O O
Wall Mounted Motor O O O
STANDARD DIMENSIONS Consult factory for larger sizes.
Width 14’4” 14’4” 14’4”
Height 8’4” 8’4” 8’4”

WARRANTY Manufacturer’s standard 5-year from date of plant shipment against defects in materials or workmanship. Spring wire is warranted for one year. C.H.I.’s obligations are strictly limited to repair or replacement of defective parts and components during the warranty period.
INSTALLATION C.H.I. Rolling Steel Doors shall be installed and adjusted according to C.H.I. assembly instructions by trained door service technicians.

S = Standard O = Optional — = Not available G = Gray W = White C = Clear anodized #4 = #4 polished P = Powder coat U = Unpainted Galvanized
1 Standard for manual and awning crank operated doors. 2 Only available with tubular stainless steel bottom bar. 3 Standard for doors up to 10’4” wide. 4 Standard for door over 10’4” wide.

Model 7500: Fire Shutter

Model 7500: Fire Shutter

Fire protection manufactured to the highest standards, C.H.I. fire shutters feature attractive, space saving designs and user-friendly operation. U.L. labeled for installation to approved drywall, masonry and steel construction, Series 7500 Fire Shutters meet all U.L. requirements for counter and window openings

SPECIFICATIONS AND OPTIONS

7522 7566
CURTAIN
Flat slat S S
Exterior Skin
22 gauge, Galvanized [G/W/P/U] S –
22 gauge, Stainless steel [#4] – S
BOTTOM BAR
11 gauge, Single angle steel [BK] S –
1/8” Single angle stainless steel [M] – S
LOCKS
Plated steel slide locks S –
Stainless steel slide locks – S
HOOD
24 gauge, Galvanized [G/W/U/P] S –
24 gauge, Stainless steel [#4] – S
GUIDES Fabricated from two formed pieces of 11 gauge steel or stainless steel to create guide channel. Guide angles include curtain stops and flared guides.
Painted steel [BK] S –
Stainless steel [#4] – S
FIRE RATING
3/4-Hour Approved Approved
1-1/2-Hour Approved Approved
3-Hour Approved Approved
OPERATION
Manual push-up [maximum size is 10’4” x 8’4”] S1 S1
Awning Crank S2 S2
Motor 0 0
STANDARD DIMENSIONS Consult factory for larger sizes
Width 13’0” 13’0”
Height 8’4” 8’4”

WARRANTY Manufacturer’s standard 5-year from date of plant shipment against defects in materials or workmanship. Spring wire is warranted for one year. C.H.I.’s obligations are strictly limited to repair or replacement of defective parts and components during the warranty period.
INSTALLATION C.H.I. Rolling Steel Doors shall be installed and adjusted according to C.H.I. assembly instructions by trained door service technicians.

S = Standard O = Optional — = Not available G = Gray W = White U = Unpainted galvanized #4 = #4 polished P = Powder coat BK = Black † = Gauge is dictated by UL procedure. Call for more information.
1 Standard on doors up to 10’4” wide. 2 Standard on doors up to 13’0” wide.

Model 7000: Guardian™ Fire Doors

Model 7000: Guardian™ Fire Doors

The Guardian™ Fire Door is engineered to meet ever-increasing demands of property owners and insurance underwriters in a simple, easy-to-test, and reset fire protection product with a U.L. label rating from ¾-hour to 4-hour protection. Manual push-up, chain hoist and automatic reset motor operation is available for Guardian™ Fire Doors and can incorporate one of several release device options. The National Fire Protection Association (NFPA) and other model codes recommend frequent drop testing of rolling steel fire doors to ensure a continuous state of operational readiness. C.H.I. strongly promotes these recommendations with the Guardian™ advanced design features

SPECIFICATIONS AND OPTIONS

7400 7401 7301 7302 7366
CURTAIN
Flat slat – S S S S
Curved slat S — — — —
Exterior Skin
22 gauge, Galvanized† [G/W/T/B/U/P] S1 S1 S2 S2 —
20 gauge, Galvanized† [G/W/U/P] S3 S3 S4 S4 —
18 gauge, Galvanized† [G/W/U/P] S4 S4 O — —
22 gauge, Stainless steel [#4] — — — — S
Interior Skin
24 gauge, Galvanized [G/W/T/B/U/P] — — — S —
INSULATION
Mineral wool — — — S —
R-Value — — — 4.2 —
BOTTOM BAR
Minimum 1/8” double angle steel [BK] S S S S —
1/8” Double angle stainless steel [M] — — — — S
HOOD
24 gauge, Galvanized [G/W/T/B/U/P] S S S S —
24 gauge, Stainless steel [#4] — — — — S
GUIDES Fabricated from three (minimum 3/16”) structural steel angles bolted together to form guide channel. Guide angles include curtain stops and flared guides.
Painted steel [BK] S S S S S
Hot dipped galvanized steel O O O O O
Cold galvanized steel O O O O O
Mill finish stainless steel — — — — O
FIRE RATING
3/4-Hour Approved Approved Approved Approved Approved
1-1/2-Hour Approved Approved Approved Approved Approved
3-Hour Approved Approved Approved Approved Approved
4-Hour Approved Approved — — —
OPERATION
Manual push-up [maximum size is 12’4” x 10’4”] O O O — O
Chain hoist S S S S S
Motor O O O O O
STANDARD DIMENSIONS Consult factory for larger sizes.
Width 24’0” 24’0” 24’0” 24’0” 13’0”
Height 24’0” 24’0” 24’0” 20’4” 24’0”

LOCKING Manual push-up doors furnished with interior slide bolt locks with padlock provision standard. Chain hoist operated doors furnished with chain hoist keeper suitable for padlocking. Optional bottom bar cylinder locking available.

WARRANTY Manufacturer’s standard 5-year from date of plant shipment against defects in materials or workmanship. Spring wire is warranted for one year. C.H.I.’s obligations are strictly limited to repair or replacement of defective parts and components during the warranty period.

INSTALLATION C.H.I. Rolling Steel Doors shall be installed and adjusted according to C.H.I. assembly instructions by trained door service technicians.

S = Standard O = Optional — = Not available G = Gray W = White T = Tan B = Brown U = Unpainted galvanized #4 = #4 polished P = Powder coat BK = Black † = Gauge is dictated by UL procedure. Call for more information.

1 Standard on doors up to 13’4” wide. 2 Standard on doors up to 18’4” wide. 3 Standard on doors from 13’5” to 18’4” wide. 4 Standard on doors from 18’5” to 24’0” wide.

Series 6000: Insulated

These coiling doors are engineered and designed for maximum strength and durability. Manufactured to stringent code standards, this Series 6000 insulated coiling door is an industrial product built to provide a high degree of confidence for specifiers and end users. A wide variety of slat profiles, gauges, and color options are available.

Series 6000: Non-Insulated

Series 6000: Non-Insulated

These coiling doors are engineered and designed for maximum strength and durability. Manufactured to stringent code standards, this Series is an industrial product built without shortcuts to provide a high degree of confidence for specifiers and end users. A wide variety of slat profiles, gauges, and color options are available.

SPECIFICATIONS AND OPTIONS

 

6241 6220 6221 6200 6201 6180 6181 6244 6266
CURTAIN
Flat slat S — S — S — S S S
Curved slat — S — S — S — — —
Flat perforated slat [G/P] — — — — O — — — —
Flat fenestrated slat† [see gauge colors] O — O — O — O O O
24 gauge, Galvanized [G/W/T/B/U/P] S — — — — — — — —
22 gauge, Galvanized [G/W/T/B/U/P] — S S — — — — — —
20 gauge, Galvanized [G/W/U/P] — — — S S — — — —
18 gauge, Galvanized [G/W/U/P] — — — — — S S — —
16 gauge (.050”), aluminum [C] — — — — — — — S —
22 gauge, Stainless steel [#4] — — — — — — — — S
BOTTOM BAR
11 gauge, Double angle [U] S S1 S1 S1 S1 S1 S1 — —
Minimum 1/8” double angle steel [BK] — S2 S2 S2 S2 S2 S2 — —
3/16” Double angle aluminum [C] — — — — — — — S —
1/8” Double angle stainless steel [M] — — — — — — — — S
Extruded aluminum (maximum width 14’4”) [C] O — O — O — O O O
HOOD
24 gauge, Galvanized [G/W/T/B/U/P] S S S S S S S S S
18 gauge (.040”) aluminum [C] — — — — — — — O —
24 gauge, Stainless steel [#4] — — — — — — — — O
GUIDES Fabricated from three (minimum 3/16”) structural steel angles bolted together to form guide channel. Guide angles include curtain stops and flared guides.
Painted steel [BK] S S S S S S S S S
Hot dipped galvanized steel O O O O O O O O O
Cold galvanized steel O O O O O O O O O
Clear anodized finish aluminum3 — — — — — — — O —
Mill finish stainless steel — — — — — — — — O
OPERATION
Manual push-up [to 80sq.ft. or £8’4” high] S O O O O O O O O
Manual push-up [to 120sq.ft. or £8’4” high] — — — — — — — O —
Chain hoist S4 S S S S S S S S
Motor O O O O O O O O O
WINDLOAD
Windbreaker Series — O O O O O O — O
Impact Series — O O O O O O — O
STANDARD DIMENSIONS Consult factory for larger sizes.
Width 12’0” 20’4” 20’4” 28’4” 28’4” 30’0” 30’0” 14’4” 18’4”
Height 14’4” 20’4” 20’4” 28’0” 28’0” 28’0” 28’0” 18’4” 20’4”

LOCKING Manual push-up doors furnished with interior slide bolt locks with padlock provision standard. Chain hoist operated doors furnished with chain hoist keeper suitable for padlocking. Optional bottom bar cylinder locking available.

WARRANTY Manufacturer’s standard 5-year from date of plant shipment against defects in materials or workmanship. Model 6241 service doors are warranted for one year. Spring wire is warranted for one year. C.H.I.’s obligations are strictly limited to repair or replacement of defective parts and components during the warranty period.

INSTALLATION C.H.I. Rolling Steel Doors shall be installed and adjusted according to C.H.I. assembly instructions by trained door service technicians.

S = Standard O = Optional — = Not available G = Gray W = White T = Tan B = Brown U = Unpainted galvanized C = Clear anodized #4 = #4 polished P = Powder coat BK = Black † = Fenestrations or windows are 5” x 1-1/8” on 7” centers. Specify number and location.

1 Standard on doors up to 14’4” wide. 2 Standard on doors over 14’4” wide. 3 Wall and pack-out angles painted steel. 4 Standard for doors over 10’4” wide and 8’4” high.

Search
close