February 2019 - Authority Garage Supply | Garage Doors | Garage Door Openers |Tampa

Model 3400: Miami-Dade County Certified Wind Load Rated Rolling Sheet Door

The Model 3400 series commercial roll up door has been specifically engineered for Miami-Dade County, Florida. With an ability to withstand high winds, the sheet metal door meets Miami-Dade County’s stringent building codes. The door is also easy to install and uses a 12” drum wheel. Other features and specific measurements of the door are as follows:

Maximum opening size of 12’ wide x 16’ high (192 sq.ft.)
Push-up, hand chain, and electric operations
PSF Ratings:
- +43 PSF and -49 PSF

DOWNLOAD FLYER

Curtain

24-gauge galvanized corrugated steel
Grade 80 galvanized steel
Available in white only
Super Durable polyester paint coatings, which are corrosion resistant
Wash coat over primer interior side
40-year film integrity warranty – up to 30-year chalk and fade
Flexible nylon wear strips

Bottom Bar

24-gauge acrylic-coated galvalumed roll formed steel
2” x 1 ½” galvanized angle
Bulb astragal (Durometer 75)
Stainless steel nuts and bolts

Axle/Torque Tube

Oil tempered torsion springs conforming to ASTM A229
16-gauge, 12” diameter galvanized drum
Low friction, grease-filled steel ball bearings staked in each drum
26-gauge spiral torque tubing houses axle assembly

Guides

12-gauge galvanized steel guide, with 11-gauge windlock bar spot welded guide
Bolt on head stop ¼” thick steel
2 7/8” guide depth
Pre-punched for lock and attachment bolts
Vinyl guide wear strip

Hardware

Bottom bar mounted 10-gauge slide locks – 2 per door
Bottom bar mounted 16-gauge step plate – 2 per door
12-gauge door mounting brackets
1-5/16” tension holding device

Model 850: Miami-Dade Certified Wind Load Self Storage Door

Model 850: Miami-Dade Certified Wind Load Self Storage Door

The 24-gauge corrugated door curtain is manufactured from full hard galvanized grade 80 steel and coated with Super Durable polyester paint that is backed by a 40-year film integrity and a 25 year no-fade limited paint warranty. Independently tested, the Model 850 meets the requirements of the Miami-Dade County Product Control Division for the high velocity hurricane zone (HVHZ) of the Florida building Code. Design wind load is rated +46 PSF and -54 PSF. Available in opening sizes up to 8’8” x 10’0” and in white only.

DOWNLOAD FLYER

Door Springs

During production, each spring is coated with a generous amount of grease that penetrates the pores of the spring with additives, displacing moisture and preventing the formation of rust and corrosion. In addition, this process relieves the friction created between spring coils thereby providing smoother door operation. Finally, the spring and axle assembly is enclosed in a tube to protect them from the elements encountered throughout the life of the door.

Optional Package Protection and Shipping

Doors stacked on top of each other in transit are going to shift… unless they can be packaged in a way to minimize the sliding that occurs during that time. Janus has found the way. As an option, we can suspend each door individually in crates. Whether they travel down the block or across the country, compaction damages, door abrasion and chatter marks are virtually eliminated.

Ratchet Tensioning Device

The Janus ratchet tensioning device supplied as standard equipment on our door offers a simpler method of tensioning while more accurately fine tuning all the springs on the door at the same time. There is no extra hardware required. Eight different positions on the tension wheel allow one to perfectly balance the door every time. There are no pins required to hold the tension on the spring. You simply just click it.

Radial Ball Bearings

Janus supplies radial ball bearings at no additional cost. Our permanently lubricated bearings require no maintenance and are guaranteed to last the entire life span of the door.

Dead Axle and Torque Tube Assembly

This design, noted for its durability and smoother operation with commercial applications, has now been incorporated into the Janus self-storage door. The tube housing protects the springs and strengthens the axle. Eliminating axle push and shift that can occur with a live axle, the dead axle design allows for a straighter travel path of the door curtain in the guides. The biggest feature of this design is that it affords the fine tuning of any spring adjustment to equally affect all springs on the door at the same time.

Latching

Our patented mini latch features a cover plate made from a heavy gauge yellow zinc coated steel or optional stainless steel. In addition, the latch cover protects the slide from tampering by completely covering the slide, with the exception of a tab used to operate the latch. To further secure the door, the latch’s two-inch throw, with its magnetic properties, can be incorporated with the new guide-mounted security devices. This versatile design affords you the ability to utilize padlocks, cylinder locks or both.

Model 750: Certified Wind Load Self-Storage Roll Up Door

Janus International has achieved wind load certification with the Series 750 Steel Roll Up Door. The Series 750 Certified Wind Load Self Storage Door was designed to meet stringent wind load requirements for mini storage applications while still providing the best door operation in the industry. The innovative door design has minimized the locking and reinforcement needed to strengthen the door to pass rigorous wind load testing.

Product Brochure

FEATURES

FEATURES

Minimizes the locking and reinforcement needed to strengthen the door to pass rigorous wind load testing.
Fewer friction points and less additional weight results in a door that operates better and still yields greater strength than any other available to the self-storage industry.
Meets the requirements of the SBC (Standard Building Code) and ASCE 7 (American Society of Engineers). The ASCE Standard is used in the Florida Building Code and the International Building Code.
Applicable opening sizes range from 3’ wide through 10’ wide, with the maximum height being 12’
Locking device may be located on the curtain or the bottom bar.
Doors may be installed on steel, concrete, or filled block jambs
All door sizes meet the wind load requirements of the interior and exterior zones for 100 mph SBC wind speed and 130 mph exposure B, ASCE 7 wind speed.
Higher wind load ratings are available for certain sizes and can be determined on an individual basis.

Model 650: Self Storage Roll-Up Doors

The Janus International Series 650 steel roll up door has been designed and manufactured to give self-storage facility owners a high amount of value, as the 650 mini storage roll up doors are extremely durable and require virtually no maintenance. Janus doors provide long term savings that it brings when installation, maintenance, and replacement costs. Each metal roll up door comes with a three year workmanship and material warranty. Additionally, a 40-year film integrity and a 30 year no-fade policy for the paint

Product Brochure

Door Springs

Coated with grease during production, which prevents rust and corrosion
Enclosed in a tube for lifetime protection
Provide for smooth door operation

Ratchet Tensioning Device

Allows for simplified spring tensioning
Tensions all springs at once
Requires no pins to hold the tension on the spring

Radial Ball Bearings

Provided at no additional cost
Permanently lubricated
Require virtually no maintenance

Dead Axle and Torque Tube Assembly

Tube housing protects springs and strengthens the axle
Eliminates axle push and shift that a live axle would create
Allows for springs to be turned all at the same time

Model 3100: Certified Wind Load Rated Metal Roll Up Doors

The Janus International 3100 series is our certified wind load rated model that has been manufactured to withstand strong wind forces. Independent laboratory testing has verified that the Model 3100 steel roll up door meets stringent building codes, while the included one-year warranty ensures its quality

Product Brochure

Wind Load

Designed to meet stringent building codes in coastal regions
Utilizes 12” drum wheel
Maximum opening size of 20’ wide x 14’ high (280 sq. ft.)
Push-up, hand chain and electric operations
PSF Ratings:
- +35 PSF and -41 PSF for opening widths through 12’
- +35 PSF and -38 PSF for opening widths over 12’ through 16’

Curtain

26’gauge galvanized corrugated steel
Grade 80 galvanized steel
20 standard colors (special colors upon request for a nominal upcharge)
Super Durable polyester paint coatings, which are corrosion resistant
Wash coat over primer interior side
40-year film integrity warranty – up to 30-year chalk and fade
Flexible nylon wear strips

Bottom Bar

24-gauge acrylic-coated galvalumed roll formed steel
2” x 1 1/2” galvanized angle
Bulb astragal (Durometer 75)

Guides

12-gauge galvanized steel guide, with 11-gauge windlock bar spot welded guide
Bolt on head stop ¼” thick steel
2-7/8” guide depth
Pre-punched for lock and attachment bolts
Vinyl guide wear strip
Universal jamb mount

Hardware

Bottom bar mounted 10-gauge slide locks – 2 per door
Bottom bar mounted 16-gauge step plate – 2 per door
12-gauge door mounting brackets

Model 283: Mini/Self-Storage Windlock Sheet Door

Model 283: Mini/Self-Storage Windlock Sheet Door

Asta Door model 283 continuous corrugated windlock steel roll-up door is produced with the highest quality and durability in the industry. The Model 281 is available in sizes up to 10×10 and in a variety of colors. Excellent price and efficient installation make the Model 281 the perfect choice for mini/self-storage building, portable carports, or any storage applications.

Curtain

Sheet: 26-gauge galvanized steel roll formed in continuous corrugation. Galvanized according to A.S.T.M. A653-60 and finished with baked epoxy primer and baked polyester topcoat.
Windload: Door construction designed to satisfy windload of +30.0/-34.0 psf at 8’0” wide tested to +45.0/-51.0 psf. Consult factory for available sizes or higher windloads.
Bottom Bar: Curtain to be reinforced with a bottom bar consisting of a continuous 2” x 1-1/2” x 12-gauge galvanized steel angle with E.P.D.M. astragal.
Windlock Clip: 10-gauge galvanized clip riveted to curtain edge with two 3/16” rivets.

Spring Counterbalance

Drum Assembly: To be formed with 28-gauge galvanized steel sheet rolled around and attached to stamped 18-gauge galvanized steel drums to restrict deflection to .03” per food (2.5 mm/m) of door width.
Springs: To be helical torsion type oil tempered wire designed to cycle 12,500 times with an overload factor of 25%. Springs are to be mounted on a 1” (25.4mm) black steel pipe of minimum 14-gauge.

Operation

Rope Pull: To be ¼” (6.35mm) polyester rope attached to bottom angle.

Support Brackets

Support Brackets: 10-gauge galvanized plate bracket with tension adjustment device.

Weather Seal

Side Draft Seal: Brush seal with aluminum retainer (field installed).
Top Draft Stop: to be E.P.D.M. seal attached to top of curtain to seal against header (field installed).

Guide Assembly

Guides: To be roll formed 18-gauge galvanized steel channels with P.V.C. wearstrips.

Locking

Curtain Lock: to be hardened galvanized steel slide bolt attached to curtain suitable for padlocking. (padlock by others)

Installation

To be by Asta Door Corporation authorized representative according to Asta Door Corporation standards and instructions.

Model 281: Mini/ Self-Storage Sheet Door

Model 281: Mini/ Self-Storage Sheet Door

Asta Door model 281 continuous corrugated steel roll-up door is produced with the highest quality and durability in the industry. The Model 281 is available in sizes up to 10×10 and in a variety of colors. Excellent price and efficient installation make the Model 281 the perfect choice for mini/self-storage building, portable carports, or any storage applications.

Curtain

Sheet: 26-gauge grade 80 full hard galvanized steel roll formed in continuous corrugation. Galvanized according to A.S.T.M. A653-60 and finished with baked epoxy primer and baked polyester topcoat.
Side Stripping: P.V.C. rubber to be attached to curtain edges.
Bottom Bar: Curtain to be reinforced with a bottom bar consisting of a continuous 2”x1-1/2”x14 gauge galvanized steel angle with E.P.D.M. astragal.

Drum Assembly

Drum Assembly: To be formed with 28-gauge galvanized steel sheet rolled around and attached to stamped 18-gauge galvanized steel drums to restrict deflection to .03″ per foot (2.5 mm/m) of door width.
Springs: To be helical torsion type oil tempered wire designed to cycle 12,500 times with an overload factor of 25%. Springs are to be mounted on a 1″ (25.4mm) galvanized steel tubing minimum 14-gauge.

Support Brackets

Support Brackets: 10-gauge galvanized plate bracket with tension adjustment device.

Operation

Rope Pull: to be 1/4″ (6.35mm) polyester rope attached to bottom angle.

Guide Assembly

Guides: to be roll formed 18-gauge galvanized steel channels with P.V.C. wear-strips.

Locking

Curtain Lock: to be hardened galvanized steel slide bolt attached to curtain suitable for padlocking. (padlock by others)

Model 203: Windlock Commercial Sheet Door

Model 203: Windlock Commercial Sheet Door

Asta Model 203 continuous corrugated windlock steel roll-up door is produced with the highest quality and durability in the industry. The Model 203 is available in sizes up to 20×18 in a variety of colors. Excellent price and efficient installation make the Model 203 the perfect choice for loading docks, warehouse buildings, distribution centers, freight terminals, or any commercial applications with high windload requirements.

Curtain

Sheet: 26-gauge grade 80 full hard galvanized steel roll formed in continuous corrugation. Galvanized according to A.S.T.M. A653-G60 and finished with baked epoxy primer and baked polyester top coat.
Side Stripping: P.V.C. rubber to be attached to curtain edges.
Windload: Door construction designed to satisfy windload of +/-35.0 psf, Tested to +/-52.50 psf at 16’0” wide. Consult factory for available sizes or higher windloads.
Bottom Bar: Curtain to be reinforced with a bottom bar consisting of a 2″ x 2″ x 3/16″ (50.8mm x 50.8mm x 4.76mm) structural steel angle with E.P.D.M. astragal.
Wind-Lock: To be 10-gauge galvanized 1100 Wind-Lock clips riveted to door curtain edge.

Drum Assembly

Drum: To be formed with 26-gauge galvanized steel sheet rolled around and attached to stamped 16-gauge galvanized steel drums to restrict deflection to .03″ per foot (2.5 mm/m) of door width.
Springs: To be oil tempered, grease packed helical torsion type designed to cycle 12,500 times with an overload factor of 25%. Springs are to be mounted on a 1-5/16″ hot rolled steel tubing minimum 11 gauge.

Support Brackets

Support Brackets: to be 3/16″ (4.76mm x 4.76mm) thick structural steel angles and a 1/4″ (6.35mm) thick steel diagonal brace welded in a triangular form to support ends of drum assembly.

Operation

Chain Hoist: To be cast iron pocket wheel drive with machine link hand chain.

Guide Assembly

Guides: To be roll formed 12-gauge galvanized steel channels with welded 10-gauge Windlock 1100 insert.
Guide Depth: 3-1/2” deep per side to provide sheet penetration adequate to satisfy specified windloading.

Weather Seal

Side Draft Seal: Brush Seal with aluminum retainer (field installed).
Top Draft Stop: To be E.P.D.M. seal attached to top of curtain to seal against header (field installed).

Locking

Hand Chain Lock: Bracket, to be mounted on guide angle or wall for chain operated doors.
Curtain Lock: To be hardened galvanized steel slide bolts attached to bottom angle suitable for padlocking. (padlock by others)

Model 201: Commercial Sheet Door

Model 201: Commercial Sheet Door

Asta Model 201 continuous corrugated steel roll-up door is produced with the highest quality and durability in the industry. The Model 201 is available in sizes up to 12×16

Curtain

Sheet: 26-gauge galvanized grade 80 full hard steel roll formed in continuous corrugation. Galvanized according to A.S.T.M. A653-G60 and finished with baked epoxy primer and baked polyester topcoat.
Side Stripping: P.V.C. rubber to be attached to curtain edges
Bottom Bar: Curtain to be reinforced with a bottom bar consisting of 2” x 1-1/2” x 12-gauge galvanized steel angle with E.P.D.M. astragal.
Various accessories and options available.

Drum Assembly

Drum: To be formed with 26-gauge galvanized steel sheet rolled around and attached to stamped 16-gauge galvanized steel drums to restrict deflection to .03” per foot (2.5 mm/m) of door width.
Springs: To be oil tempered, grease packed helical torsion type designed to cycle 12,500 times with an overload factor of 25%. Springs are to be mounted on a 1-5/16” (25.4 mm) hor rolled steel tubing of minimum 14-gauge.

Support Brackets

Support Brackets: To be 3/16” (4.76mm) thick structural steel angles and ¼” (6.35 mm) thick steel diagonal brace welded in a triangular form to support ends of drum assembly.

Operation

Rope Pull: To be 1/4″ (6.35mm) polyester rope attached to bottom angle up to 10′ x 10′ (3048mm x 3048mm) doors.
Chain Hoist: To be cast iron pocket wheel drive with machine link hand chain for over 10′ X 10′ (3048 mm x 3048 mm) doors.

Guide Assembly

Guides: To be roll formed 16-gauge galvanized steel channels.
Guide Depth: 2-1/2” deep per side to provide sheet penetration adequate for proper operation.

Weather Seal

Side Draft Seal: Brush seal with aluminum retainer (field installed).
Top Draft Stop: to be E.P.D.M. seal attached to top of curtain to seal against header (field installed).

Locking

Hand Chain Lock: bracket, to be mounted on guide angle or wall for chain operated doors.
Curtain Lock: to be hardened galvanized steel slide bolts attached to bottom angle suitable for padlocking. (padlock by others)

Model 6500: Counter Shutter

Model 6500: Counter Shutter

The 6500 series roll-up doors offer the best in security, flexibility, and appeal. Reduced sized slats provide for smoother operation and a more aesthetically pleasing appearance. End users and specifiers recognize the 6500 Series as state-of0the-art in design, fit, and finish, yet appreciate the simplicity and practically that define the product.

SPECIFICATIONS AND OPTIONS

	6522	6544	6566
CURTAIN
Flat slat	S	S	S
Exterior Skin
22 gauge, Galvanized [G/W/P/U]	S	–	–
16 gauge (.050”), Extruded aluminum [C/P]	–	S	–
22 gauge, Stainless steel [#4]	–	–	S
BOTTOM BAR
Extruded aluminum [C]	S	S	–
11 gauge, Stainless steel	–	–	S
Tubular stainless steel	–	–	0
LOCKS
Thumb turn lock and handle	S1	S1	O2
Keyed lock and handle	0	0	02
Best cylinder	0	0	02
Stainless steel slide locks	–	–	S
HOOD & HEADPLATE COVERS
24 gauge, Galvanized [G/W/T/U/P]	S	–	–
20 gauge, Aluminum [C/P]	–	S	–
24 gauge, Stainless steel [#4]	–	–	S
GUIDES Fabricated from two pieces of extruded aluminum or formed stainless steel to create guide channel. Guide angles include curtain stops and flared guides.
Extruded aluminum [C]	S	S	S
11 gauge, Stainless steel [#4]	—	—	O
OPERATION
Manual Operation	S3	S3	S3
Awning Crank	O4	O4	O4
Tube Motor	O	O	O
Wall Mounted Motor	O	O	O
STANDARD DIMENSIONS Consult factory for larger sizes.
Width	14’4”	14’4”	14’4”
Height	8’4”	8’4”	8’4”

WARRANTY Manufacturer’s standard 5-year from date of plant shipment against defects in materials or workmanship. Spring wire is warranted for one year. C.H.I.’s obligations are strictly limited to repair or replacement of defective parts and components during the warranty period.
INSTALLATION C.H.I. Rolling Steel Doors shall be installed and adjusted according to C.H.I. assembly instructions by trained door service technicians.

S = Standard O = Optional — = Not available G = Gray W = White C = Clear anodized #4 = #4 polished P = Powder coat U = Unpainted Galvanized
1 Standard for manual and awning crank operated doors. 2 Only available with tubular stainless steel bottom bar. 3 Standard for doors up to 10’4” wide. 4 Standard for door over 10’4” wide.